Hello again kids. It’s time to lance another of my favorite audio hot air balloons (notice I stayed away from the zit metaphor out of consideration for you gentile reader). Today we will answer the questions:
- How much power do I need?
- Which is better: Tubes or Transistors?
- How much do I need to spend?
Let’s start with the how much power do I need part.
We need to go back and take another walk around your listening room.
The size of your room and the speakers you have selected are the two things we need to discover.
The larger your room (and the farther you sit from your speakers when you listen) is of primary interest. A typical bedroom for example should never require more than about 100 watts RMS (total of two channels) even with inefficient acoustic suspension speakers. This assumes an “honest” low distortion 100 watts RMS over the audible frequency range. RMS stands for “Root Mean Square” which simply means it can supply the power for any possible musical material. And yes, rock is usually more demanding on average but classical is usually more demanding for peaks. RMS power can handle either situation. And by “low distortion” we usually look for no more than 0.1% at full power output. And it must be able to supply this “honest” 100 watts over the entire range of hearing (unless you are a dog in which case you will need to pay more for an amp that will cover the ultrasonic frequencies we can’t hear).
But what about volume? What if I like my Led Zeppelin cranked to 11?
Whoa. Back up the bus. What’s the goal here? To paint the audio illusion that you are there or they are hear in a way that can not be distinguished from the original. As discussed, unless a rock band is recorded live (you would definitely be there) it is most unlikely there was an “original” to emulate other than what came out of the studio monitors when the recording was made. And the sound pressure levels at a rock concert is subject for another blog (and another set of ears to damage thank you verry much).
An acoustic orchestra or a vocalist with an ensemble is something which can be reproduced because it was actually produced. And it is this which the honest 100 watts can provide in your 10 x 16 bedroom with startling authenticity.
But what if I have very efficient speakers? Won’t I be better off with an amplifier with a lower power rating?
Nah. That’s what the volume knob is for. Set it on 4 instead of 8.
Okay, what about my living room which is much larger?
How much larger? This is where things can get expensive. Your ears don’t play fair when it comes to loudness. In theory, to make an instrument or vocalist sound twice as loud, (or sound the same except from twice as far from the speakers), a ten fold increase in amplifier power is needed. This assumes your speakers can handle this much power. So 100 watts suddenly becomes 1000 watts.
But wait! There’s good news! Remember the listening room you just built a few entries back? It has walls and a floor and ceiling which always reflect some of the sound to your ears. And there is another really good thing about your brain to keep in mind. We have a hard time remembering exactly how loud something was originally. So the naked truth is, if you get the sonic details correct (directionality, frequency range, tonal balance, waveform integrity, dynamic range, all the responsibility of the guy behind the glass), and you have taken care to properly play his product (on your choice of sources / more about these in coming chapters), and your speakers are capable of faithfully following the electrical power your amplifier is working so hard to send to them, the actual sound pressure level (volume) is not a deal breaker. All will be well in the land of audio reproduction. The musicians will be magically transported to here or you to where they are.
In a large family room or living room even with relatively inefficient speakers, 500 watts RMS total of 2 channels (with the same assumptions discussed previously) is more than enough for any real world acoustic material.
So which is better, tubes or transistors?
There is no better (or worse). Only more or less accurate. And accuracy can be scientifically quantified.
An amplifier has only one job. Gain. A perfect amp will take a “small” musical waveform and make it much “larger”. That’s all. It will not add or subtract or in any way change anything except “size”. Transistors and tubes are devices which allow us to do this. Neither is perfect. They both contribute subtle changes to the waveform. But as long as their contributions are within objective measurable (distortion) limits, it does not matter.
So how much should I spend for a 500 watt amp?
You should buy (spend) whatever you want and can afford on an amp that makes you happy. That’s a different question from what do I need to spend for an amp that will bring them here or me there. That’s where profit margin distortion comes in. There are some very nice folks that will sell you a spiffy new amp with any imaginable feature. And damn are they pretty. So go for it if it makes you happy and your checkbook is up to the task.
But truth be told, spending more than about two bucks a watt is just not necessary in order to have a convincingly life like copy of Yo Yo Ma playing cello in your listening room.
Next time: What’s All the Vinyl Hoopla About?